Bostik smart adhesives

Bostik smart adhesives

Mostrando 1–9 de 30 resultados

  • Air pressured gun APG 600

     259.74

    Closed airpressure gun for 600 ml sausages.

  • Bostik Easy Clean Wipes (10 pieces in one box)

     22.39

    Waterless cleaning towels.  Effectively removes adhesives, sealants, tar, wax, grease, oil and other hard to remove substances from tools and equipment. Features Cleans tools and equipment. Convenient, easy tear off towels. No rinsing, no drying and no residue. Tough on dirt, soft on hands Pre-moistened, disposable, multi purpose. Waterless. Convenient packaging allows for easy dispensing. Scrub side effectively lifts dirt, soft side generally wipes away. Recommended Uses For tools and equipment. Removing dirt, adhesives, sealants, tar, wax, grease, oil, lubricants, paint, ink and most hard to remove substances. Multi purpose cleaner.

  • Cleaner 14

     18.65

    Product Simson Cleaner 14 is a thin liquid product for cleaning and degreasing substrates before sealing or bonding with specific Simson products. Consult the Technical Data Sheet of the particular product. Applications v Cleaning and degreasing of closed substrates. v Removing uncured sealant- and adhesive remains on substrates and tools. Method of use Substrates must be dry. Firmly rub the substrates with a clean, colourless cloth or tissue paper wetted with Cleaner 14. In case the substrate is strongly contaminated repeat this once more. Replace the cloth when it becomes dirty. Avoid contamination in the tin. Always close the tin immediately after use. Only pre-treat as much surfaces that can be sealed or bonded within 6 hours. Application temperature: between +5°C and +30°C. Drying time: after a drying time of 5 minutes the sealant or adhesive can be applied. Note: It is recommended to make a trial in advance on a small piece to check whether the substrate will be affected by Cleaner 14. Plastics and lacquers can be especially sensitive.

  • Cleaner E

     16.17

    Simson Cleaner E is a pretreatment product for cleaning and degreasing substrates before sealing or bonding with specific Simson products. Cleaning and degreasing joints in teak wood decks (prior to the application of Simson Prep P). Removing uncured sealant and adhesive remains from substrates and tools. Degreasing and cleaning glass substrates.

  • Cleaner I

     29.45

    Product Simson Cleaner I is a preparation agent, ideally suitable for cleaning and degreasing substrates for bonding or sealing with specific Simson products. Consult Technical Data Sheet of the particular product. Applications  Cleaning and degreasing of ceramic coated glass.  Cleaning and degreasing of plastic.  Cleaning and degreasing of closed substrates (consult Bostik for more information).  Removing uncured sealant and adhesive, based on Silyl Modified Polymer (SMP) from substrates and tools. Method of use The substrates should be firmly rubbed with a clean, colourless cloth, wetted with Cleaner I. In case the substrate is strongly contaminated repeat this once more. Note: It is recommended to make a trial in advance on a small piece, to check whether the substrate will not be affected by Cleaner I. Drying time: It is recommended to allow a drying time of 5 minutes (at 20ºC/50% R.V.). In case of any doubt please consult Bostik.

  • Fireseal S 310ML White (Cartridge)

     20.04

    Product Simson FireSeal S(ilicone) is a fire-retardant, neutral curing silicone sealant. Applications Suitable for both inside and outside applications in building construction, ship/yacht building and industry. For sealing (connection) joints, around window frames, outlets through walls and floors of pipes, cables, ventilation ducts etc. and as glazing sealant. Features v Solvent free and free of halogenated additives. v Permanently elastic. v Good UV- and weather resistant. v Tested on fire resistance by a.o. TNO and Warrington. v Complies to DIN 4102 class B1. v Tested according to IMO-resolution A.687 (17). Method of use Substrates: Substrates must be solid, clean, dry and dust- and grease/oil free. On porous substrates such as concrete, cellular concrete, gypsum and fibre cement Simson Primer MSP is recommended. On bare metals such as anodised aluminium, stainless steel, galvanised steel, copper, lead and zinc the use of Simson Prep M is recommended. Joint construction: Requirements to the joint construction should be at least the same - as far as fire resistance is concerned - as requirements to the total (wall)construction. The fire resistance of the joint construction can be increased considerably by sealing the joint both sides. To increase the fire resistance it is better to use non flammable materials such as mineral wool or ceramic cord or blanket instead of regular backing foam. The joint depth of expansion joints should be roughly 2/3rd of the joint width. Both depth and width should be at least 6 mm. Application: Extrude FireSeal S to the backing material with a hand- or air pressure gun. Tooling: Because of skin forming press the sealant to the sides of the joint within 10 minutes with a spatula or pointing trowel and smoothen immediately. A light soap solution prevents sticking of the sealant to the tool. Avoid penetration of soap solution between sealant and joint wall, because this can create loss of adhesion. Cleaning: Cured sealant is not soluble and can be removed mechanically only (e.g. with a razor blade or by sanding). Combustibility Low flammable as per DIN 4102 Class B1 in applications in (max. 40 mm wide) joints between solid mineral building materials.

  • Hand Gun PZ 600

     75.83

    Closed handgun for 600 ml sausages (and cartridges)

  • Liquid 1

     19.35

    Product Simson Liquid 1 is a thin liquid cleaning agent for surfaces and tools especially to remove fresh remains of primers, sealants and adhesives. Applications v Cleaning of fresh remains of primer- and adhesive remains on cladding panels. v Cleaning of fresh remains of bituminous roof sealant (Simson Elastoroof). Features Non-aggressive cleaner which -generally speaking- does not attack surfaces of cladding panels. Method of use Rub the surfaces firmly with a clean colour free cloth soaked in Liquid 1. If the surfaces are still very contaminated repeat once more. Note: Test on a small scale if the surfaces are resistant to the volatile contents of Liquid 1. Especially plastics and lacquers may be damaged. Application temperature: +5°C till +30°C. Drying time: At least 10 minutes drying time is recommended. After cleaning the surfaces with Liquid 1 please check if Liquid 1 has evaporated completely.